1.4 TDI 90bhp ATL engine intake manifold flap motor fix (?)

The one on my new project (2005 BHC engine) was showing the Motor for Intake Manifold Flap (V157)

I removed the intake manifold and opened it. Below are the pictures of the inside, it is immaculate inside it.

However, what I found was that there was so much gunk around the EGR valve that it had completely blocked up the airflow therefore car wasn't able to get any any air and hence unable to start!


A thorough clean out of the EGR valve worked a treat and no errors now!


20170501_134642.jpg
20170501_134648.jpg
20170501_140800.jpg
20170502_132837.jpg
20170502_140617.jpg
 
Wow just found this great info in here.

Better not driving the car i guess until I've had a chance to see if I can salvage the intake manifold before I wreck it by not fixing. Hopefully as above its just full of oil!

Future reference I have an ATL engine reporting intake flap motor issue
 
Last edited:
ok in the end I've just used a bit of kitchen towel and some metal cleaner for the stubborn bits on the outer casing along with the inside of the manifold itself (where the actual air goes through as there was a lot of stubborn oil marks in there).

I did find some oil in there and it was in amongst the cogs which I cleaned up with a dry kitchen roll and finished off with silicon lubricant once all was back in place.

i am finding though at the extreme closed off position even when clean it is sticking closed at times - is this normal? if not it might explain the issue and I'm not sure if I'm able to fix it.

On the electronics side there wasn't a massive amount of oil either but what there was I cleaned up with combo of kitchen roll and cotton buds dipped in acetone then dried off.

Will reinstall over the weekend and find out what happens - at least if it doesn't work I know how to put the new one in :)
 
Did you take the motor out and clean it? Mine is still working fine by the way. The spring-return on my is quite strong, and did not stick when tested by hand. All the best. Matt


Sent from my iPhone using Tapatalk
 
when you had it apart , you say the flap was sticking , firstly were there any burs on the brass flap or any sideways movement as posibly sticking on the sides of the alloy casing , after i modified my amf one and had it welded up i noticed my flap would stick slightly at fully closed position , on inspection i found a tiny bur on the outer edge prob from me porting out the insides i must of knocked against it and being brass its very soft , i used some wet and dry and curved the whole flaps edges very slightly and it cured my issue .. may be of some help to you
 
Spring return does seem strong it just sticks if you put it to the extreme closed position and it will stay there until you start to move it back- it then springs back quickly. I followed the excellent guide and took the top off the main gear and cleaned off the oil I could see.

Will take a look at the inside again as I suspect it could be hard to get at crud (oil).

I'm tempted to use a fairly strong solution of degreaser but any gotchas on that - could I cause indirect issues?
 
Last edited:
i always use brake cleaner to remove the gunge in those throttle valves with a tooth brush ... never had or heard of anybody having issues
 
So refitted today and cleared error. Car shut off and much smoother...then light came back on!

Decided to take the car for a short run then cleared the error again.

Took the car for another 5 mile run and EML error did not come back on this time.

For sure shutting the car off is way smoother but not 100% sure the error will not come back only time will tell.

Thanks for the great info on the thread!
 
Last edited:
Right so after EML light came back on, removed and and dirt build up from egr was removed and replaced it then came back on again so whilst for sure it is smoother I'm guessing there is something else up with it. :(

Before I replace with a new manifold any further ideas?

I've spotted this one of eBay is not OEM but it's quite a bit cheaper!

http://www.ebay.co.uk/itm/Butterfly-Valve-Control-Flap-Audi-VW-POLO-9N-1-4-TDI-Seat-Ibiza-A2-045128063d/282672145842?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m1438.l2649
 
As a final update I picked up a VDO replacement for £190 from ebay. Fitted just there in 10 minutes and the difference is pretty stark if I'm honest.

I thought the clean up of the old one had smoothed things out but this is a whole new ball park. Smooth start and very smooth shut off so whilst this was the expensive option compared the attempted clean up I'm guessing the clean up isn't always successful so a replacement is the last resort...
 
  • Like
Reactions: oko
So the ASV smooths the start not just shut off ? Always wondered as my starts used to be smoother, shut downs intermmitent as has was the EML light.
Thanks for that. Does anyone know if there is an easy way to extend the distance between EGR and ASV by an inch or two ? I need more clearance for the Bosch tandem pump.
Cheers
Martin
 
Wow ok so EML light back on this morning for 3103 intermittent.

For sure the shut off is way smoother but EML must be getting triggered by wiring short or cccu issue maybe rather than the flap itself?

Light eventually went off by itself. Weird..
 
Last edited:
AS a follow up on this EML light and fault is still registering despite intake motor without doubt working perfectly.

I washed the car today and on it came.

I'm of the opinion I have a wiring harness issue here where the motor plugs in - might even just be just a cut in the wire but how I go about fixing / replacing this without major surgery i dont know.
 
Following up I re adjusted the rubber hose at the join to the metal pipe running to the intercooler. Didn't make an immediate impact until I cleared the codes off.

Despite weeks of snow, rain and very cold temperatures... including around 400 miles it hasn't come back on.

I know updating this may have tempted fate but given the length of time, extreme conditions and distances I'm hoping its now fixed. I can only assume that the hose wasn't properly aligned onto the metal pipe causing air and indeed water ingress.
 
The fault came back 2 weeks ago (shortly after I fixed my starting issue:rolleyes: if you saw the thread). Last night I had time to strip the V157 again. There was only a little oil in it this time, only really enough to wet the outside of the motor and coat the inside of the casting in a few places and I wiped out what I could.
I suspect that the first time, the cleaning of the motor brushes and commutator didn't work very well because I used meths instead of a proper oil solvent like paraffin.
This time I swilled the motor out in paraffin instead, dunking it up and down a few hundred times and letting it fill and empty in a jar full. I turned the motor a good deal whilst immersed. The paraffin quickly went black, so I think the cleaning has been much more effective.
After re-assembling and clearing the fault code, all is well again. Hopefully this time it will last more than 16 months before needing to be done again.

Matt
 
After 4 error free months and all fingers pointing at a dodgy ecu the eml came on again this morning. I'm now utterly convinced is related to water as I had the bonnet off during a torrent last night. In addition I think my months of issues could have been water escaping from a disconnected ns washer nozzle dowsing the motor. This was what I was fixing last night! Id never noticed it in the whole time ive owned the car and i just thought a2 washers were rubbish... they aren't!
So question is should the motors be sensitive to water or could it be something like an exposed wire or slight leak sucking in water ?

I've cleared for now and hopefully water should now no longer get anywhere near...

If anything this whole saga does build character
 
So after convincing myself that I could have been unlucky and received a new faulty VDO intake flap motor (installed since Oct 2017) I contacted the supplier and they were happy to change over given I explained everything else that had been tried.

I replaced on Saturday....I plugged my ipod classic into the car just now with the car sitting with the ignition on - then I decided to start the car as the ipod wasn't getting enough juice and hey presto the EML light came back on with the SAME error. P3103 -35 -10 Intermittent 19559 Intake Flap motor faulty (as from vcds lite).

Its BRAND NEW and is NOT faulty...ECU has been replaced also and EGR is out of the equation as its been mapped out (or could it still be affecting things?)

Is there a fuse anywhere that controls the flap motor - I cant see anything under the dash?

Could it be hoses? Timmus checked the wiring to the flap and its good.
 
Back
Top